Everything about Fuller Weapon totally explained
A
Fuller is a rounded or beveled groove on the flat side of a blade, such as a
sword,
knife, or
bayonet (shown). The purpose is to strengthen or lighten the
blade, rather than to allow blood to flow from a stabbed person. A well made knife will have a
forged Fuller to increase the strength in the spine of the blade. If the Fuller has been cut or ground out of the blade, the spine is weaker. Many blades use fullers even when they're so short that the physical effect is negligible; in this case, the purpose may be to make the weapon resemble larger blades.
The blood-groove (which is often incorrectly called a fuller) is similar in appearance but is very different in function. Rather than creating a groove, a hole is cut out nearly the entire length of the blade. (The fact that it's referred to as a blood-
groove likely causes the incorrect assumption that the two designs are synonymous.) Theoretically this design feature makes a weapon easier to withdraw after a stabbing attack by allowing air into the wound it produces, but no evidence has demonstrated any resisting suction effect. It is important to note that this also weakens the spine of the blade.
Physics
The basic design principle is that
bending causes more
stress in material near the edge or back of the blade than material in the middle, due to
leverage. The diagram at right shows stress distribution in an ideal blade with a rectangular section, with only a small amount of shear stress present at the neutral axis. Fullers remove material from near this neutral axis, which is closer to the blade's spine if only one edge is sharpened (see photo above). This yields stiffer blades of a given weight, or lighter blades of a given
stiffness. The same principle is taken to an extreme in the
I-shaped cross sections of most steel
beams. Some even contend that this concept was borrowed into architecture from weapons design
(External Link
).
Japanese blades
In
Japanese
bladesmithing, fullers have a rich tradition and terminology, enough that there are separate terminologies for the top (hi, usually pronounced as bi when used as a successive word) and bottom (tome) ends of the feature. A listing follows:
- Hi
- Bo-bi: A continuous straight groove of notable width, known as katana-bi on tanto. With soe-bi, a secondary narrow groove follows the inner straight length of the main one. With tsure-bi, the secondary is similar but continues beyond the straight length.
- Futasuji-bi: Two parallel grooves.
- Shobu-bi: A groove shaped like the leaf of an iris plant.
- Naginata-bi: A miniature bo-bi whose top is oriented opposite from the blade's, and usually accompanied by a soe-bi. Seen primarily on naginatas.
- Kuichigai-bi: Two thin grooves that run the top half of the blade; the bottom half is denoted by the outer groove stopping halfway while the inner one expands to fill the width.
- Koshi-bi: A short rounded-top groove found near the bottom of a blade, near to the tang.
- Tome
- Kaki-toshi: The groove runs all the way down to the end of the tang.
- Kaki-nagashi: The groove tapers to a pointed end halfway down the tang.
- Kaku-dome: The groove stops as a square end within 3 cm of the tang's upper end.
- Maru-dome: Similar to the kaku, except with a rounded-end.
The kukri
The
Nepali
kukri has a terminology of its own, including the "aunlo bal" (finger of strength/force/energy), a relatively deep and narrow fuller near the spine of the blade, which runs (at most) between the handle and the corner of the blade, and the "chirra", which may refer either to shallow fullers in the belly of the blade or a hollow
grind of the edge, and of which two or three may be used on each side of the blade
(External Link).
Further Information
Get more info on 'Fuller Weapon'.
|
External Link Exchanges
Do you know how hard it is to get a link from a large encyclopaedia? Well we're different and will prove it. To get a link from us just add the following HTML to your site on a relevant page:
<a href="http://fuller__weapon.totallyexplained.com">Fuller (weapon) Totally Explained</a>
Then simply click through this link from your web page. Our crawlers will verify your link, extract the title of your web page and instantly add a link back to it. If you like you can remove the words Totally Explained and embed the link in article text.
As long as your link remains in place, we'll keep our link to you right here. Please play fair - our crawlers are watching. Your site must be closely related to this one's topic. Any kind of spamming, dubious practises or removing the link will result in your link from us being dropped and, potentially, your whole site being banned. |
